How to Replace the Water Filter on a Whirlpool Refrigerator

Learn how to replace the water filter on your Whirlpool refrigerator following these simple steps. Don’t forget to replace your filter every 6 months!

Checkout this video:

Tools and Parts Needed

Before you begin, gather the tools and parts you will need to complete the repair:
-a Phillips screwdriver
-a quart of clean water
-a new water filter (Whirlpool Filter 4396841, $49.00 on Amazon)

Parts may vary depending on your model refrigerator, so be sure to check your owner’s manual for the correct part number before ordering.

Preparing the Fridge for the Filter Change

To replace the water filter on your Whirlpool refrigerator, it is first necessary to prepare the fridge for the change. This process is simple and only takes a few minutes.

First, locate the small knob or switch on the front of your fridge that controls the ice maker. On most models, this switch is located near the top of the fridge, on the left-hand side. If your model does not have a switch, there will be a knob that controls the ice maker.

Next, turn off the ice maker by rotating the knob or flipping the switch to the “Off” position. Once the ice maker is off, remove any ice cubes that are in the ice tray. If your model has an external water dispenser, rotate the knob or switch to the “Off” position.

Now that your fridge is prepared, you can proceed to changing the water filter.

Replacing the Filter

Replacing the water filter on your Whirlpool refrigerator is easy to do, and only takes a few minutes. You’ll need to know the model number of your refrigerator, which is usually located on the inside of the fridge door or on the back panel. Once you have that, head to your local home improvement store or an online retailer that sells Whirlpool parts.

  Does Zero Water Pitcher Come With Filter?

Most filters last for six months, but it’s a good idea to check yours every few months to make sure it’s still working properly. To replace the filter, start by unscrewing the old one from the housing. Then, insert the new filter and screw it in place. Make sure it’s snug so that there are no leaks.

Once you’ve replaced the filter, flush out the water lines by running water through them for a few minutes. This will clear out any residual dirt or debris that may be left behind. Now you can enjoy fresh, clean water from your Whirlpool refrigerator!

Resetting the Filter Change Indicator

If your refrigerator model has a Filter Change Indicator (also called a Reset Water Filter, or RFID Light), it will notify you when it’s time to change your water filter cartridge. The indicator is typically a small light that’s either red or green. It’s usually located on the control panel, near where you insert the new water filter.

When you replace the cartridge, you need to reset the indicator so it will know to start counting down again until the next time the filter needs to be changed. Here’s how to do it:

1. Locate the Filter Change Indicator on your control panel.
2. Press and hold the button for 3 seconds. You should see the light turn green or hear a beep to indicate that the indicator has been reset.
3. Continue with steps 4-6 in the “How to Change a Whirlpool Refrigerator Water Filter” instructions above.

Tips and Tricks

It’s easy to forget about your fridge’s water filter — until you go to pour yourself a glass of water and nothing comes out. If you have a Whirlpool refrigerator, chances are you’ll need to replace the water filter every six months or so. Here are a few tips and tricks to help you do just that:

  How To Clean Your Pur Water Filter

-To start, locate your refrigerator’s water filter. It should be located in the upper right-hand corner of the fridge, behind a small panel.

-Once you’ve located the water filter, use a quarter turn counterclockwise to release it from the housing.

-Next, take the new filter and insert it into the housing. Make sure that it is inserted correctly by turning it clockwise until it locks into place.

-Finally, flush the new filter by running water through it for about three minutes. Doing this will remove any contaminants that may be present in the filter.

FAQs

Q: How often should I replace the water filter in my Whirlpool refrigerator?
A: For the best possible results, we recommend replacing your Whirlpool refrigerator’s water filter every 6 months.

Q: Where can I find my model number?
A: You can find your model number on the inside wall of your refrigerator, on the left-hand side behind the Crisper Drawer.

Q: What are the symptoms of a worn-out water filter?
A: As your water filter starts to wear out, you may notice a decrease in water pressure, or that your ice cubes are smaller or have less flavor.

Conclusion

Now that you know how to replace the water filter on your Whirlpool refrigerator, you can be sure that your family is always getting clean, filtered water. Be sure to check the filter every few months and replace it when it starts to look dirty.

Scroll to Top